Audio – TrendNet Security Ltd https://trendnet.com.cy Your Trusted Source for Security Products Fri, 05 Jun 2026 02:28:15 +0000 en-US hourly 1 https://wordpress.org/?v=7.0 CasaTunes 2 Channels X 100W Amplifier https://trendnet.com.cy/product/casatunes-2-channels-x-100w-amplifier/ https://trendnet.com.cy/product/casatunes-2-channels-x-100w-amplifier/#respond Fri, 05 Jun 2026 02:28:14 +0000 https://trendnet.com.cy/product/casatunes-2-channels-x-100w-amplifier/
  • Class-D amplifier providing 100 watts/channel (RMS) into 8 ohm loads or 125 watts/channel into 4-ohm loads
  • Bridgeable output provides 225 watts into a single 8-ohm load
  • 4-pole detachable speaker screw connector (Phoenix connector) with support for up to 12 AWG speaker wire
  • 12-volt trigger input for power-on/off
  • 12-volt trigger output for controlling other devices
  • Buffered loop output of original signal for connecting additional amplifiers
  • Rear panel volume gain adjustment
  • Built-in thermal and short circuit protection circuits
  • Includes rack-mount ears for mounting a single unit, or two units side-by-side
    • ]]>
  • Audio Inputs: Stereo Analog RCA
  • Audio Outputs: Buffered stereo analog RCA loop output
  • Output Power: 100 watts per channel into 8 ohms (0.1% THD+N), or 125 watts per channel into 4 ohms (0.5% THD+N), or 225 watts into a single 8 ohm load (0.2% THD+N)
  • Minimum Output Impedance: 4 ohms in stereo mode, 8 ohms in mono bridged mode
  • Trigger Input: 12 VDC, 10 kΩ
  • Trigger Output: 12VCD, 100mA
  • Input Power: 100 – 240 VAC, 50/60Hz, 2.5A
  • Standby Power Consumption: ≤ 0.5 watts
  • Dimensions: 8.5” x 10.5” x 1.8” (216 x 267 x 45 mm)
    • ]]>     https://trendnet.com.cy/product/casatunes-2-channels-x-100w-amplifier/feed/ 0     Artsound Arcus-EDS KNX Interface for Smart Audio products https://trendnet.com.cy/product/artsound-arcus-eds-knx-interface-for-smart-audio-products/ https://trendnet.com.cy/product/artsound-arcus-eds-knx-interface-for-smart-audio-products/#respond Fri, 05 Jun 2026 01:17:52 +0000 https://trendnet.com.cy/product/artsound-arcus-eds-knx-interface-for-smart-audio-products/ The KNX-GW-IP-2TE is used for coupling the ETS ( PC software tool ) via Ethernet to the KNX bus for addressing and programming KNX components.

    Using the KNX-group monitor allows for the monitoring and transfer of telegrams via the KNX-bus in real time. The site of the KNX-group monitor is subdivided into a configuration and a telegram section.

    The KNX-IP-gateway is able to save telegrams. The KNX-telegram logger lists the saved telegrams. It is possible to set a timeframe as well as a group address filter.

    To visualize the data, up to three different group addresses can be displayed in one graph.

    The gateway can link html-sites with KNX-files and visualize them in every browser, provided that websockets are supported.

    ]]>
  •  Operating voltage: 9 .. 30VDC max. 1,5W  2-pin terminal with screws
  •  Terminal bus voltage: KNX 2-pin terminal ( red / black )
  •  Power consumption (KNX): Approx. 120mW (at 24V DC)
  •  Ambient temperature: Storage -25 .. +85°C
  •  Operation -25 .. +55°C
  •  Ethernet: 10/100 Mbit/s RJ45
    • ]]>     https://trendnet.com.cy/product/artsound-arcus-eds-knx-interface-for-smart-audio-products/feed/ 0